LE-PC7XCL is a Windows® PC software which can remotely control an analyzer equipped with the OP-SB7XC/OP-SB7XL (expansion board for in-vehicle communication such as CAN) from a PC and capture communication data in measurement to the PC for analysis. It supports the combination of expansion board OP-SB7XC/OP-SB7XL and protocol analyzer LE-3500XR(V2)/LE-2500XR(V2).
For more details: https://www.lineeye.com/html/p_LE-PC7XCL.html
LE-PC300R is Windows? software which enables a PC to control LINEEYE protocol analyzers from remote in order to use measurement data of those analyzers on a PC.
It is compatible with the following analyzers: LE-3500XR(V2), LE-2500XR(V2), LE-3500XR, LE-2500XR, LE-3500R, LE-2500R, LE-1500R, LE-110SA, LE-120SA, LE-3500, LE-2500, LE-1500
For more details: https://www.lineeye.com/html/p_LE-PC300R.html
The LE-270GF is a small and lightweight CAN/CAN-FD/LIN communication data logger with a built-in acceleration sensor, capable of GPS positioning compatible with QZSS SLAS (Sub-meter Level Positioning Augmentation Service), and capable of measuring analog voltages up to 32V. It can be used in two modes: logger mode, which allows continuous recording of measurement logs to a large-capacity SD card by itself, and remote mode, which connects to a personal computer (hereinafter referred to as PC) via Wi-Fi or USB as a CAN/CAN-FD/LIN communication analyzer and displays measurement data of communication, positioning, acceleration, and analog voltage in real-time on the PC. In remote mode, multiple analyzers can be remotely measured from one PC and continuously recorded on the PC's HDD, etc., and you can compare and analyze multiple communication lines. It also has a test transmission function that allows pre-registered test communication data to be selected on the PC and repeatedly transmitted, which is useful when developing communication devices. It is resistant to momentary power outages and can be used where there are water droplets. As it consumes low power it can be widely used for installation in test vehicles and integration into inspection lines.
For more details: https://www.lineeye.com/html/p_LE-270GF.html
The LE-270AF is a small and lightweight CAN/CAN-FD/LIN communication data logger capable of measuring analog voltages up to 32V. It can be used in two modes: logger mode, which allows continuous recording of measurement logs to a large-capacity SD card by itself, and remote mode, which connects to a personal computer (hereinafter referred to as PC) via Wi-Fi or USB as a CAN/CAN-FD/LIN communication analyzer and displays measurement data of communication, positioning, acceleration, and analog voltage in real-time on the PC. In remote mode, multiple analyzers can be remotely measured from one PC and continuously recorded on the PC's HDD, etc., and you can compare and analyze multiple communication lines. It also has a test transmission function that allows pre-registered test communication data to be selected on the PC and repeatedly transmitted, which is useful when developing communication devices. It is resistant to momentary power outages and can be used where there are water droplets. As it consumes low power it can be widely used for installation in test vehicles and integration into inspection lines.
For more details: https://www.lineeye.com/html/p_LE-270AF.html
LE-150PF is a lightweight communication protocol analyzer has a Data Logger function to record data in the SD card for long hours. It is an entry model designed for Asynch communication. While succeeding all the excellent cost-performance of LE-150PR, it also supports remote control by Wi-Fi.
Attention: The Wi-Fi module used for this product conforms to SRRC (China), FCC (USA), CE (EU), TELEC (Japan), KCC (Korea), IC (Canada) and NCC (Taiwan). However Wi-Fi function is allowed to use only in Japan, USA, Canada, and EU.
For more details: https://www.lineeye.com/html/p_LE-150PF.html
LE-200PF is a small and lightweight communication protocol analyzer equipped with a communication data logger function that can continuously record communication data on an SD card for long periods of time. Like the previous multi-protocol model LE-200PR, it can analyze many communication standards and also supports logic analyzer waveform display.
Attention: The Wi-Fi module used for this product conforms to SRRC (China), FCC (USA), CE (EU), TELEC (Japan), KCC (Korea), IC (Canada) and NCC (Taiwan). However Wi-Fi function is allowed to use only in Japan, USA, Canada, and EU.
For more details: https://www.lineeye.com/html/p_LE-200PF.html
LE-650H2 is the hardware-based USB analyzer, which can record a large amount of data on the HDD/SSD of the PC, display translation with each class decode, and measure VBUS power consumption. The analyzer automatically detects the High/Full/Low speed of USB2.0/1.1 and starts measuring by simply pressing the space bar of the PC. The low cost device of easy operation by connecting it to the USB port of the PC is useful for developing/debugging the firmware/driver and study purpose of USB standard.
Selectable USB charger AC Plug Types
LE-3500XR(V2) inherits all the functions of the conventional model LE-3500XR, such as the analysis test function of RS-232C, RS-422/485, TTL communication data, and expansion of communication measurement targets by adding options, while also being equipped with new functions that can be used as an analog measurement logger. In addition, the USB 2.0 device port has been changed from the conventional micro-B connector to the Type-C connector, which has been widely used in recent years.
During development testing of communication systems, it can be used as a high-performance protocol analyzer, and during normal development when voltage and temperature measurement and recording are required, it can be used as a high-precision data logger.
* To use it as an analog measurement logger, the analog pod (optional, sold separately) is required.
For more details: https://www.lineeye.com/html/p_LE-3500XRV2.html
Selectable USB charger AC Plug Types
LE-2500XR(V2) inherits all the functions of the conventional model LE-2500XR, such as the analysis test function of RS-232C, RS-422/485, TTL communication data, and expansion of communication measurement targets by adding options, while also being equipped with new functions that can be used as an analog measurement logger. In addition, the USB 2.0 device port has been changed from the conventional micro-B connector to the Type-C connector, which has been widely used in recent years.
During development testing of communication systems, it can be used as a high-performance protocol analyzer, and during normal development when voltage and temperature measurement and recording are required, it can be used as a high-precision data logger.
* To use it as an analog measurement logger, the analog pod (optional, sold separately) is required.
For more details: https://www.lineeye.com/html/p_LE-2500XRV2.html
SI-60FP is an interface converter to connect equipment such as factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix LAN module
converts serial data into LAN protocol (TCP/IP). SI-60FP supports a wide range of temperature (-20 to 55 Celsius). It has the robust metal body and supports 35mm DIN rail.
Selectable AC Plug Types
LE-150PF is a lightweight communication protocol analyzer has a Data Logger function to record data in the SD card for long hours. It is an entry model designed for Asynch communication with excellent cost-performance.
This set includes:
Handheld analyzer for CAN/LIN with touch screen.
The LE-590TX is a LAN analyzer that connects to a PC's USB2.0 port. In TAP mode, you can capture full duplex data on 10/ 100Base-TX and transmit to the PC at 480Mbps via the USB2.0 interface. In PG mode, you can generate test packets at up to 100Mbps line rate.
Handheld analyzer for TTL(1.8V-5V) with touch screen.
Handheld analyzer for ASYNC with touch screen.
SI-35USB is an USB converter, which converts USB of PC into RS-422/RS-485.
SI-35USB-2 is an USB converter, which converts USB of PC into RS-422/RS-485.
LA-5R(G) is a digital I/O unit which outputs five relays via LAN (Ethernet). With an input unit (LA-5P-P(G) etc.), it can built an input-output system without using a PC. 
LA-3R3P-P is a digital I/O unit which inputs 3 dry contact and outputs 3 relays via LAN (Ethernet). 
LA-5P-P(G) is a digital I/O unit with which you can monitor five dry contact inputs of the unit via LAN
(Ethernet). 
Applicable Analyzers: LE-3500XR/LE-2500XR
Applicable Analyzers: LE-3500XR/LE-2500XR
16GB SD Card
External Automotive Antenna
32GB SD Card
This is the cable for LE-270GR / LE-270AR to monitor CAN communication by connecting to OBD2 connector. This cable can power the analyzer through OBD2 connector by using 16th pin of the OBD connector and it does not need any other external power source. You can log CAN data by using the analzyer and this cable in the car.
Applicable Analyzers: LE-3500R, LE-2500R, LE-1500R, LE-3500, LE-2500, LE-1500
To mount the analyzer on the 35mm DIN rail.
A cable with test clips suitable to the external trigger of 4 inputs or 4 output connector.
Probe cable with clips for CAN measurment and with IC test clips for LIN measurement.
A screw terminal adapter to convert RS-530 port into terminals.
An adapter to extract the RS-422/485 signals on the DSUB 25pin connector to the terminal block.
A probe pod for monitoring TTL-level communication lines at 2.5V/3.3V/5V.
Applicable Analyzers:
Selectable AC Plug Types
Branch cable for measuring RS-232C over DSUB 9pin of PC, etc.
Applicable Analyzers: LE-3500/LE-2500/LE-1500